Skip to main content

Concrete Stain & Epoxy in Palm Beach & Martin County

Ground, repaired and sealed concrete coatings for garages, patios, pool decks and commercial floors that resist stains, wear and moisture.

Bare concrete in South Florida soaks up moisture, oil and dirt, and it starts to look stained and dusty soon after it is poured. A coating seals the slab and gives it a finish that is easy to clean. Coastal Paint & Design installs epoxy, polyaspartic and stain systems on garage floors, lanais, patios, pool decks, driveways, warehouses and showrooms. Each system is chosen for where the floor is and what it has to handle day to day.

Grinding is what makes a coating stay down. We use diamond grinding equipment to open the surface of the concrete and remove old sealers, paint and contaminants, which gives the base coat a mechanical bond. Acid etching is a shortcut we avoid because it does not profile the slab as consistently. Cracks and divots are filled with epoxy or polyurea repair material, and a moisture test tells us whether the slab needs a vapor-blocking primer.

For looks, chip flake systems blend colored flakes into the base coat and hide dust and small imperfections. Metallic epoxy gives a flowing, polished look suited to showrooms and finished garages. Solid colors keep a clean commercial appearance, and acid stain brings out a mottled, stone-like tone in the concrete itself. Every system is sealed with a topcoat that resists hot tire pickup, oil and everyday wear.

What's Included

  • Moisture testing and inspection of the slab
  • Diamond grinding to remove contaminants and profile the surface
  • Crack, joint and divot repair
  • Epoxy or polyaspartic base coat
  • Chip flake broadcast, metallic or solid color finish
  • Acid stain finishes for a natural stone look
  • UV-stable, chemical-resistant topcoat
  • Non-slip additive for areas that get wet

Surfaces We Work On

Garage floors
Garage slabs take hot tires, oil drips and dropped tools, so they get a full grind and a chemical-resistant topcoat.
Pool decks
Outdoor pool decks need UV-stable products and a non-slip texture that holds up in direct sun.
Patios and lanais
Covered and open patios can be coated or stained to complement the house and resist mildew.
Driveways and walkways
Exterior concrete is cleaned, repaired and coated with systems built to handle sun and standing water.
Warehouses and showrooms
Commercial floors get solid color or metallic systems that are easy to sweep and mop.
Interior concrete floors
Acid stain or metallic epoxy can turn a bare interior slab into a finished floor.

How Long It Lasts in South Florida

A properly applied epoxy or polyaspartic garage floor lasts ten to twenty years with normal residential use. The biggest factor is prep: floors that are diamond ground and repaired before coating hold up far better than those that were acid etched or simply rolled. Outdoor concrete has a harder life. Direct sun, heat swings and water push coatings to their limits, which is why exterior jobs call for UV-stable products.

Moisture rising through the slab is a hidden cause of failed floor coatings in South Florida, where the water table sits close to the surface. Testing for it before coating, and using the right primer when it is present, protects the system from lifting. After installation, sweep grit regularly, wipe up oil and chemicals promptly, and set pads under jack stands, ladders and heavy equipment.

Our Prep Process

  1. 1

    Assess the slab

    We check for cracks, old coatings, oil saturation and moisture, which tells us which system and primer the floor needs.

  2. 2

    Clear and degrease

    The area is emptied, swept and degreased so grinding does not push oil and dirt deeper into the surface.

  3. 3

    Diamond grind

    Industrial grinders profile the concrete and strip sealers and contaminants, with dust collection keeping the work area cleaner.

  4. 4

    Repair defects

    Cracks, spalls and divots are filled and ground flush so the finished floor is level and uniform.

  5. 5

    Apply base and topcoat

    The base coat goes down, with flakes or metallic pigment added where chosen, followed by the protective topcoat.

  6. 6

    Cure and hand back

    Most garage floors take foot traffic in 24 hours and vehicles in 72 hours, and we walk the floor with you before you use it.

Concrete Stain & Epoxy FAQ

How long does an epoxy garage floor last?

With normal residential use, a properly applied epoxy or polyaspartic garage floor lasts ten to twenty years. What decides where yours lands in that range is surface prep, the grade of product used, and whether the topcoat is UV-stable so it will not yellow or peel near the garage door. We diamond grind rather than acid etch for that reason.

Can you coat outdoor concrete like pool decks and patios?

Yes. For pool decks, patios and walkways in direct sun, we use UV-stable polyaspartic and acrylic systems. They resist fading and peeling and handle the heat swings that make many coatings fail on outdoor concrete in South Florida. Non-slip texture is added so the surface stays safer underfoot when it gets wet.

What is the difference between epoxy and polyaspartic?

Epoxy is very durable and builds a thick, hard film, but it can yellow in sunlight. Polyaspartic cures faster, stays UV-stable and can be applied in a wider range of temperatures. We often combine them, using an epoxy base coat for build and a polyaspartic topcoat for UV resistance and a quicker return to service.

How soon can I use my floor after it is coated?

Most residential garage floors are completed in one to two days. You can usually walk on the surface within 24 hours and park vehicles on it after 72 hours. Outdoor areas and larger commercial floors may take longer depending on size, weather and the system chosen, and we give you a specific schedule before work starts.

Should I choose chip flake or metallic epoxy?

Chip flake floors have colored flakes broadcast into the base coat. They hide dust, tire marks and small slab flaws, and add a little texture underfoot. Metallic epoxy creates a swirled, glossy look with depth and suits showrooms and finished garages where appearance matters most. Solid color is the simplest option for a clean, uniform floor.

Will a coated floor be slippery?

Coatings can be slick when wet, so we add non-slip aggregate to the topcoat. The amount can be adjusted: more texture for pool decks and wet entries, less for an interior garage where easy cleaning matters most. Chip flake systems add some grip on their own. Tell us how the floor is used and we will match the texture to it.

Ready for Concrete Stain & Epoxy?

Request a free estimate or call (561) 251-6165.