Skip to main content

Concrete Stain & Epoxy in Jensen Beach, FL

Ground, repaired and sealed concrete coatings for garages, patios, pool decks and commercial floors that resist stains, wear and moisture.

Concrete Stain & Epoxy for Jensen Beach Homes

Sand, salt water and fishing gear all end up on Jensen Beach garage floors, and bare concrete absorbs those stains quickly. An epoxy or polyaspartic coating seals the slab so spills wipe up and salt residue rinses away. We grind the concrete, repair cracks and apply a system matched to how you use the space.

For patios, walkways and outdoor showers, slip resistance matters as much as looks. We use stains, sealers and textured coatings suited to wet, sunny areas near the beach and the lagoon. We explain the options for each surface, then give you a written scope and schedule before any work starts.

What's Included

  • Moisture testing and inspection of the slab
  • Diamond grinding to remove contaminants and profile the surface
  • Crack, joint and divot repair
  • Epoxy or polyaspartic base coat
  • Chip flake broadcast, metallic or solid color finish
  • Acid stain finishes for a natural stone look
  • UV-stable, chemical-resistant topcoat
  • Non-slip additive for areas that get wet

Want the full picture? Read our complete concrete stain & epoxy guide or see everything we do in Jensen Beach.

How We Prepare and Apply

  1. 1

    Assess the slab

    We check for cracks, old coatings, oil saturation and moisture, which tells us which system and primer the floor needs.

  2. 2

    Clear and degrease

    The area is emptied, swept and degreased so grinding does not push oil and dirt deeper into the surface.

  3. 3

    Diamond grind

    Industrial grinders profile the concrete and strip sealers and contaminants, with dust collection keeping the work area cleaner.

  4. 4

    Repair defects

    Cracks, spalls and divots are filled and ground flush so the finished floor is level and uniform.

  5. 5

    Apply base and topcoat

    The base coat goes down, with flakes or metallic pigment added where chosen, followed by the protective topcoat.

  6. 6

    Cure and hand back

    Most garage floors take foot traffic in 24 hours and vehicles in 72 hours, and we walk the floor with you before you use it.

Concrete Stain & Epoxy in Jensen Beach: FAQ

Do you paint condos on Hutchinson Island in Jensen Beach?

Yes, we paint condo interiors and refinish cabinets in Jensen Beach buildings on Hutchinson Island. Before starting, we review the association's rules on work hours, parking, elevator use and contractor requirements, and we plan around them. If exterior colors or finishes need association review, we can provide samples and product data sheets for that submission.

How does living on the lagoon affect exterior paint in Jensen Beach?

Homes facing the Indian River Lagoon get steady wind, moisture and salt, so paint tends to chalk and fade faster on those sides of the house, and metal starts to rust sooner. A good wash before painting, careful caulking, rust treatment and coastal grade coatings all help the finish last. Regular rinsing between repaints helps too.

Can you work on an older cottage in Jensen Beach?

Yes. Older Jensen Beach homes often have wood siding, wood windows and many coats of earlier paint. We scrape and sand loose areas, prime bare wood and caulk open joints before painting. If we find soft or rotted wood during prep, we will point it out so it can be repaired before it is painted over.

How long does an epoxy garage floor last?

With normal residential use, a properly applied epoxy or polyaspartic garage floor lasts ten to twenty years. What decides where yours lands in that range is surface prep, the grade of product used, and whether the topcoat is UV-stable so it will not yellow or peel near the garage door. We diamond grind rather than acid etch for that reason.

Can you coat outdoor concrete like pool decks and patios?

Yes. For pool decks, patios and walkways in direct sun, we use UV-stable polyaspartic and acrylic systems. They resist fading and peeling and handle the heat swings that make many coatings fail on outdoor concrete in South Florida. Non-slip texture is added so the surface stays safer underfoot when it gets wet.

What is the difference between epoxy and polyaspartic?

Epoxy is very durable and builds a thick, hard film, but it can yellow in sunlight. Polyaspartic cures faster, stays UV-stable and can be applied in a wider range of temperatures. We often combine them, using an epoxy base coat for build and a polyaspartic topcoat for UV resistance and a quicker return to service.

Ready for Concrete Stain & Epoxy in Jensen Beach?

Request a free estimate or call (561) 251-6165 and we will set up a time to see your Jensen Beach property.